Did you know?

8. Install the front panel and secure it with the two retaining screws. 9. Close the Load Center front door. Fasten the two spring latches. 10. Switch the power on to the IntelliTouch Load Center. 11. Proceed to the “Connect the ScreenLogic Indoor Wireless Transceiver to the ScreenLogic Protocol Adapter” on page 8.Once you click on "Configure Screenlogic" on the first screen, you'll click the larger "Configure Screenlogic" on the second screen. On the "General Settings (1 of 5)" page there is a button near the bottom of that page "Set Remote Access Password". Click that and set your password. When away from the house start the SL app and click the ...Go to your IntelliCenter and from the Home screen, select Settings > Advanced System Configuration > System. Next to System Information, you will see your firmware version on the System screen. If your firmware is 1.047, click Firmware Update and follow the screens under Step 2 and select Firmware 1.064.If you need to reset your Pentair ScreenLogic password, there are a few steps you’ll need to follow. First, open up the ScreenLogic software on your computer and click on the “Settings” tab. Next, click on the “Change Password” option. This will bring up a new window where you can enter in your old password and then create a new one.Right button: Select LOW, MED or HI for the backlight brightness setting. Press the Back button to save the settings and to return to the previous screen. Settings Menu: Power Save. This option sets the time that the EasyTouch wireless control panel will shut down if there is no control panel activity.Pool Equipment. Automation. How To Set The Time Clock On The Pentair Easy Touch. Heres a video showing you how to achieve the correct time on the easy touch. How To Set Your Time Clock On Pentair Easy Touch.The IntelliChem controller will automatically set a high and low alarm for the pH level. The Delay time is the amount of time between the detected alarm condition and when the IntelliChem controller displays the alarm message on the main screen. The Delay setting is adjusted in increments of 15 seconds.Resetting your Pentair Easy Touch is a simple process: • Turn off the breaker for at least 10 seconds. • Press and hold both the Up and Down arrow buttons on the control panel simultaneously until all lights flash once. • Release the buttons, then press any button to confirm reset.Screenlogic® Remote Pool Monitoring Software. Pool & Spa. Pool Education & Support. Homeowner Support.LINKS TO PURCHASE:IntelliCenter System (Load Center with i5P Personality Kit) (523448): https://www.epoolsupply.com/products/pentair-intellicenter-system-i5p...9.Press Left button to exit to main screen. POOL/SPA MODE 1. Press Menu button until Advanced 8/14 displays. 2.Press Right button to access Advanced menu. 3.Press Right button until System Mode displays. 4.Press Up/Down button to select Pool/Spa. 5.Press Right or Left button to exit to main screen. Set Clock (5/14)Right button: Select LOW, MED or HI for the backlight brightness setting. Press the Back button to save the settings and to return to the previous screen. Settings Menu: Power Save. This option sets the time that the EasyTouch wireless control panel will shut down if there is no control panel activity.provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying this equipment (no smaller than 12 AWG or 3.3 mm). The bonding lug(s) provided on this unit are intended to connect a minimum of one No. 8 AWG for US installationThe IntelliChlor SCG is designed only to produce chlorine. The IntelliChlor SCG does not monitor or control chlorine levels in the pool or spa water. It is the pool ownerʼs responsibility for monitoring and maintaining free chlorine levels at the APSP recommended range of 2.0 to 4.0 parts per million (ppm).Run the communication cable from the pump to the enclosure. Insert the cable conductors into the one of the plastic grommet fittings, located on the lower left side of the enclosure and pull the cable up through the low voltage to the PL4/ EasyTouch PL4/PSL4 Control Systems circuit board. See illustration on page 19.How to switch from service to auto – Pentair EasyTouch. Previous. Water Slide. Next. How to switch from service to auto – Pentair EasyTouch. Filter. How to backwash a DE filter; How to clean a DE filter; Pump. How to prime a pool pump; Vacuuming And Cleaning. How to set up a manual vacuum;Once you have located the reset button on your Pentair device, follow the steps below to reset it: Step 1: Turn off the power supply to your Pentair device. Before attempting to reset your Pentair device, make sure to turn off the power supply. This will prevent any electrical shock or damage to the device. Step 2: Press the reset button.Jan 30, 2016 · This session of Pool School by Presidential Pools, Spas & Patio Service Manager, Bill Watson, explains how to program the Pentair Easytouch Automation Panel.

Either the water temperature sensor, or the Pentair Intellitouch i5s system, is giving me bad temperature readings. I have to manually start/stop the heater every time. In the beginning, the temperature reading on the remote was 50-75 degrees hotter than the water actually was. Now, the display shows a constant -186° regardless if the water is ...Clean/tighten pins as needed. DONE DONE Reset power to Heater and Reset power to Heater retry. Heater should fire. and retry. Heater should fire. ETi 400 High Efficiency Pool and Spa Heater Installation and User's Guide Rev. C 4/2017... Page 51: Diagnostics Leds: Ps, Hls, Tf, Ign, Afs, Ag1, Ag2, FsThe EasyTouch Indoor Control Panel is designed to be used with the EasyTouch 8 system. The EasyTouch 8 can automatically control your pool and spa equipment, lights and other optional equipment. You can also control all of the Pentair EasyTouch system operations from the outdoor control panel located in the Load Center at the pool equipment pad.Resetting the codes on a Kenmore dishwasher requires the owner to press all the control panel buttons, in order, within five seconds of each other. After pushing the buttons, the d...

IF you have pentair intellibrite 5G color changing LED lights, you would need to go into the light settings, and tell the easy touch that the relay is connected to IB5G's to change the color. If you don't have IB's and try to do this, you'll probably blow the bulb to an incandescent light. If it is an LED color changing light, cycling the power ...The Pentair EasyTouch Control system comes with some striking features. I have listed 6 of the most important features below. 1. Easy Touch system is available either for Eight-Function systems or Four-Function systems. 2. The Pentair EasyTouch Control system supports several types of equipment like variable speed pumps, heaters, landscape and ...If you need to reset your Pentair ScreenLogic password, there are a few steps you'll need to follow. First, open up the ScreenLogic software on your computer and click on the "Settings" tab. Next, click on the "Change Password" option. This will bring up a new window where you can enter in your old password and then create a new one.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Step 3: Restart the pump. Locate the reset button on the control pane. Possible cause: Follow these steps to configure multiple remotes: First, go to the Outdoor .