Did you know?

Blue and Yellow and Red (All 3 lights flashing simultaneously): This means the unit cannot find the Dump or Home position. The unit will not cycle automatically and needs repair. Remove the Internal Shield If your Litter-Robot was built before February of 2018, you may have an Internal Shield. A blinking check engine light means that the onboard diagnostic system detected a problem with the engine. A blinking light, rather than a steady light, often indicates a serious engine misfire. A driver with a blinking light should head di...Litter-Robot by Whisker November 14, 2016 · If you've been troubleshooting issues with your Litter-Robot Open Air to no avail, try this Fresh Restart to eliminate confounding conditions and identify the problem if there is one.First, turn off your litter robot and unplug it from the base. Then, the bonnet and the globe should be removed carefully. It will help us in reaching comfortably to the components of your litter’s robot. When you will open the globe and remove the bonnet, a …Add Litter 1 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is indoors on a firm, level surface and in a cool, dry location. Must not be touching any walls. Place litter mats or rugs in front of the unit. The Litter-Robot will now perform an initial clean ...Quick question. I got a litter robot 2 for about 2 years. It stop working today. The “empty” and “cycle” bottoms doesn’t work but only reset bottom works and “ready” is flashing blue. If I push the “reset” bottom, “cycling” is flashing yellow in 4 times per sec. The problem didn’t solve after I cleaned up pinch pins. If your Litter-Robot 3 is displaying a red power light while trying to onboard, there are several things we need to check. ... The lower left LED Ready light should now be solid blue. Wait 5 to 10 seconds, then enter onboarding mode again by pressing both the Cycle and Empty buttons together for approximately 3 seconds or until the Power button ...Emptying the Waste Drawer when indicated is important to ensure that your Litter-Robot continues to cycle automatically. Troubleshooting. A flashing Blue Light is normal, indicating the Waste Drawer is full. If your unit displays a flashing blue light or you received a “drawer full” notification in the Whisker App, please follow these steps:Jul 22, 2020 · Litter-Robot 4 consumer? Visit our assist guide on troubleshooting Litter-Robot 4 lights. Litter-Robot 3 lights: Faster quotation guide. If you’re looking for a quick reference guide on whole the Litter-Robot 3 lights, drive the digital user here or button on this image below. Litter-Robot 3 flashing bluish light Wait 1 minute. Plug it back in. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty buttons. Enter onboarding mode again by pressing both ...1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in 3.) Allow the unit to complete a startup cycle. If the light is solid blue, the code has been successfully cleared. If the light is still blinking, let’s proceed with troubleshooting.If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the Cat Sensor or Bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful. If your unit is not displaying a solid blue light after ...For the dark space I buy: "Litter-Robot 3 Bonnet LED Circuit Board Assembly" For the blue light blinking I buy: "Litter-Robot 3 Pinch Contact & DFI Kit"Edite...If the lights on the control panel blink, right to left, left to right or together, the problem is still the same: the robot has failed to track the position of the Earth correctly. That's the purpose of the Hall Effect sensor; it's what makes your Litter-Robot so intelligent. These sensors are designed to respond to any magnetic field.If your Litter-Robot 3 is displaying a red power light while trying to onboard, there are several things we need to check. ... The lower left LED Ready light should now be solid blue. Wait 5 to 10 seconds, then enter onboarding mode again by pressing both the Cycle and Empty buttons together for approximately 3 seconds or until the Power button ...The yellow light flashing quickly is due to the anti-pinch feature. The Anti-Pinch safety feature is two pin connected to the motherboard that must touch each other continuously. If they are separated, you will have an alarm (yellow blinking light). The Anti-Pinch safety is located in the top back left of the Litter-Robot base.

pjutras May 6, 2019, 1:53pm 6. Hi, The blue light will blink to indicate that the Drawer is full. If the blue light is blinking after each cycle even when you press the reset button, this mean that either there is something obstructing the way between the 2 DFI sensors or that the sensors themselves are defective.Blue and Yellow and Red (All 3 lights flashing simultaneously): This means the unit cannot find the Dump or Home position. The unit will not cycle automatically and needs repair. Remove the Internal Shield If your Litter-Robot was built before February of 2018, you may have an Internal Shield. A solid blue and yellow light may flash and remain illuminated simultaneously. This indicates that your Litter-Robot has entered its 8-Hour Sleep Mode. To deactivate this, just press and hold the Cycle button and the machine will be ready once again. However, the simultaneous flashing of all colored lights is a big problem.If you have a Litter-Robot III Open Air 3 and it's stopped working with yellow blinking / flashing light and/or the globe does not rotate in normal operating cycle or spinning continuously counter clockwise in one direction, then this video might be for you.When I first purchased the litter robot it was pretty 1 of a kind but now I'm seeing dozens of copycats with some interesting features and design on amazon. Reply ThermiteSnake ... Blue blinking light that flashes yellow frantically if I hit reset. These things are shockingly delicate. Emailed customer service :(

Litter Robot Walmart. Customer Support. The best thing about Litter-Robot is its customer support. If you’ve tried this troubleshooting method (and even tried it a few times) but it still doesn’t work, don’t hesitate to give Litter-Robot a call. Here are their details: Litter-Robot Customer Support Phone: 1-877-250-7729. 9am – 7pm ETLitter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue Solid A solid blue light means Litter-Robot is ready and safe for kitty to use. Blue Flashing If your unit’s light bar is flashing blue, this indicates that the waste drawer is …Blue is a primary color and cannot be created by mixing other colors. A light blue paint is made by mixing blue with enough white to reach the desired tint. Adding blue to a light green paint will produce a green-blue tint.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Litter-Robot 4 control panel features 5 buttons and an LED displa. Possible cause: Step 3: Check the Power Cord. If the waste drawer is not full and the sensors are clea.