Did you know?

In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...The Litter Robot Open Air III has a blinking blue light when the bottom drawer is full. This review shows what that looks like and how to fix it.Since I boug...If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app. You can now proceed with the onboarding process within the Whisker App to finalize connection.Press the Power button until the TV turns off (The red light should turn off when you do this). After that, unplug the smart TV from the power outlet for about 60 seconds. Plug the TV back in. This should fix the red blinking light, however, if the reboot doesn’t fix the red blinking light, you should try the other fixes in this guide.Help Troubleshooting Blue Flashing Light and Yellow Flashing Light (Rapidly) My Litter Robot III Open Air has a blue flashing light. When pressing Reset, the yellow light starts flashing rapidly, while the blue one is no longer lit. I tried cleaning the sensor, calibrating it, cleaning the anti-pinch safety measure. Nothing has worked so far. Litter-Robot 4 user? Visit our support guide on troubleshooting Litter-Robot 4 lights. Litter-Robot 3 lights: Quick references instruction. While you're looking forward a quick reference guide on all the Litter-Robot 3 lights, download the digital guide here or click on this figure back. Litter-Robot 3 beaming blue light. You'll most ...When I turn on the Litter Robot 3 (non-connect), blue light is flashing, then I press Reset and fast yellow light is flashing. When I press Reset again, blue light is flashing and so on.. What I checked so far: - Anti Pinch Pins looks good and are touching each other. - DFI is clean and 4 IR LEDs are blinking once a second. The yellow light flashing quickly is due to the anti-pinch feature. The Anti-Pinch safety feature is two pin connected to the motherboard that must touch each other continuously. If they are separated, you will have an alarm (yellow blinking light). The Anti-Pinch safety is located in the top back left of the Litter-Robot base.Blue, then Yellow, then Red (Flashing sequentially, one light at a time): This means the unit cannot find the dump position. Disassemble the globe and flip the magnet that is at the 1-o’clock position. Red, then Yellow, then Blue (Flashing sequentially, one light at a time): This means the unit cannot find the home position. Disassemble the ... However, recently it’s been getting stuck mid-cycle with a rapidly flashing yellow light on the “cycle” icon. I’ve tried all the trouble shooting tips including taking the cover and bonnet apart to make sure nothing was effecting the pinch mechanism. Nothing seems to be working and I’m officially at a loss. Has anyone else been able ...1.) Leave your unit powered ON with the blue blinking light engaged and unplug your power supply from the base. 2.) Wait 10 seconds, then plug the unit back in. 3.) Allow the unit to complete a start-up cycle. If the light is solid blue, the code has been successfully cleared. Now, the “ready” light flashes blue and when I press the reset button, the “cycling” light flashes yellow/amber rapidly. I Googled this and seems to be an indicator that the weight or anti-pinch sensors are being tripped (based on the flashing yellow/amber “cycling” light). I unplugged the robot and disassembled and used a q-tip to ...The Litter Robot Open Air III has a blinking blue light when the bottom drawer is full. This review shows what that looks like and how to fix it.Since I boug...Just setup the LR4 - added litter and plugged in. During its first cycle it got stuck and won’t return to the home position. The lights are flashing 3 red and 2 yellow. I emptied out all of the litter thinking I added too much and tried to reset it but it’s doing the same thing still.That alert is for the pinch sensor. Unplug it, Take the globe off and the bucket out. on the left side of the opening on the base that leads to the waste bucket there is a piece of plastic that moves a bit. That's probably stuck. It's what keeps cats from getting their paw stuck during a rotation. Clean it off and press and release it several ...Step 4: Check the Limit Switch. The limit switch tells the garage door opener when the door is fully open or closed. If the limit switch is not working properly, the status light will blink. To check the limit …That Blue flash followed by the rapid Yellow flash is indicative of a failure in the Drawer Full Indicators and Pinch Detect Terminals. If your Litter-Robot is in Warranty, give our Customer Experience Specialists a call at 877.250.7729.If your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch Safety Feature and you will need to inspect the pinch …Step 1: Check the Power. The first thing to do when it comes to troubleshooting a Litter Robot that is stuck mid-cycle is to check the power. Make sure the unit is plugged in and the power cord is securely connected to the unit and the outlet. If the power cord is loose, securely reconnect it. If the outlet is not functioning, try plugging the ...

Simply, turn on the washing machine and run a spin cycle. When your GE washing machine’s spin light is blinking endlessly, this usually means there is a fault in the washing machine that prevents it from spinning. The indicator light is designed to inform you of such faults so you can address the issue and prevent further damage to the ...Apr 25, 2022 · Blinking Blue Light, Blinking Yellow Light, and Blinking Red Lights. Mostly, the reasons for blinking blue light will be discussed. But sometimes this blue light blink gets combined with the yellow LED or red LED. So, it is necessary that you have the required knowledge of all the LEDs and what they mean. Litter robot 3.Blue light flashing constantly.Robot stopped cycling; Litter-Robot 3 doesn't work (blue blinking light) Litter robot 3 connect has slow blue blinking light or fast yellow blinking light; Litter robot 3 blinking blue light and doesn't stop; Continuous Blue flashing light; Litter Robot 3 - blaues Licht blinkt; LitterRobot 3 …I have owned my Litter Robot 3 for a little over a year and about a week ago it began to get stuck upside down when cycling. The litter box becomes unusable, and the wastebin is exposed. The yellow light is blinking. In order to fix it, I've been having to turn the unit off and back on. And even then, it will only work once before it gets stuck ...

Preparation. If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app.. You can now proceed with the onboarding process within the Whisker App to finalize connection.. When your Litter-Robot 4 has successfully …Litter-Robot Connect units only – look for the WiFi symbol on the control panel. Download the Whisker app and follow the onboarding instructions. Ensure proper placement Power on Add litter Download the app 1 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition).As of now, my litter robot will refuse to cycle or empty while flashing the same yellow light over and over. I checked the waste drawer and anything in that area, to which there is nothing seemingly wrong there. Although roughly 4 weeks ago, it was terribly packed into the U Haul which broke the litter robot (globe and bonnet popped out).…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. If your Litter-Robot 3 is displaying a yell. Possible cause: If YES, you are done. Re-position Globe and verify that it completes a cl.