Did you know?

Specification. Metric / English. A/C Belt Tensioner Bolt. 25 Nm 18 lb ft. A/C Compressor and Condenser Hose Bolt (at Accumulator) 16 Nm 12 lb ft. A/C Compressor and Condenser Hose Bolt (at Compressor) 33 Nm 24 lb ft. A/C Compressor Bolts.The tensioner bolt can also be installed and torqued down to 8 ft-lbs. The balancer shaft retaining bolts can be torqued down to 8 ft-lbs as well. The cover that keeps the oil in the engine and protects the rear timing chain can be installed with a new gasket and some silicon sealant and then torqued down to 8 ft-lbs.The 5.3 liter LS-series engine was offered from 1999-2014 and has a 3.78” bore x 3.62” stroke. The block was offered in both cast-iron and aluminum with aluminum cylinder heads. Camshaft specifications varied depending on the year and RPO code of the engine.The 1.8L starts off with 15 ft-lbs and then requires you to back them off a full turn. Then you must torque them to 26 ft-lbs and then a 90 degree turn followed by 2 more 90 degree turns and then finally a 45 degree turn by going through each bolt with each step.The fourth-gen LS intake manifold bolt torque specs are the same for all, but you also need the supercharger cover bolt torque and sequence for the LS9 and LSA, but you can find both further below. LS2 . Intake Manifold Torque Specs – 44 in-lb > 89 in-lb. Vehicles With the LS2 EngineLS Swap Guide (Gen III & IV) LS Torque Specs Swap Guide. LS Torque Specs Swap Guide. Below in this guide are the torque specs of LS based engines. These are the stock bolt torque specs, if you are running ARP bolts then refer to the instructions that came with the bolts for their torque specs. The column to the right on the guide shows a ...The LS flywheel bolt torque specs are separated into a couple of stages. In the third-generation LS and some fourth-generation ones, the first pass is 15 lb-ft, the second pass is 35 lb-ft, and the third and final torque spec is 74 lb-ft. In most versions of the fourth generation LS, the first pass is 22 lb-ft; after that, you turn the wrench ...4L80E/4L85E Torque Converter Family: Torque Converter Remanufacturing Standards. GM 4L80E / 4L85E. Replacement of all worn or damaged hubs. 100% new Friction Linings. 100% new Bearings. All Pistons machined to exceed factory trueness specs. Outer Diameter trimmed to assist with better balance and function. HD and HP versions available.Jul 30, 2023 ... 2.0t Audi VW Cylinder Head install Bolts torque specs procedure tsi tfsi b8 b8.5 ae888 replace a4. NaptownTuner•24K views · 2:54 · Go to ...Shop LS3 Chevy LS V8, Torque Converters and get Free Shipping on orders over $149 at Speedway Motors. Talk to the experts. Call 800.979.0122, 7am-10pm, everyday. REWARDS. GIFT CARDS. ... TCI 242974R Race Bolt-Together 2800-2900 Stall Converter, 6L80E. Diameter: 10" Lockup Compatible: Yes. $1,364.95 /each. Add to Cart.The 5.3 liter LS-series engine was offered from 1999-2014 and has a 3.78” bore x 3.62” stroke. The block was offered in both cast-iron and aluminum with aluminum cylinder heads. Camshaft specifications varied depending on the year and RPO code of the engine.What are the torque specs for bolting the torque converter to the flex plate? Will has the answer.Subscribe To Our YouTube Channels:COMP Cams http://www.you...Fasteners that list an angle are Torque to Yield (TTY). The specs listed are for stock fasteners. If you use ARP or other aftermarket fasteners, follow the instructions that came with your new hardware. Related Products:Camshafts & Valvetrain, Cylinder Heads, Engine Assemblies, Oiling Systems, Pistons & Piston Rings, Valve Covers & Dress-Up Kits.

When you go to install the engine into the vehicle or if it is already in the vehicle the torque specs for the exhaust manifold to the exhaust pipes or catalytic converter is 26 ft-lbs. The EGR system consists of a series of pipes that range from the manifold to the head. The EGR pipes can be torqued down to 22 ft-lbs. The LS1 flywheel is reused, and it goes on before the spacer. Torque converter bolt holes in the flywheel must be elongated to fit the non‐LS1 torque converter bolt circle. GM Performance Part #809‐12563532 Crankshaft Spacer Bolt Must be used withWood decks and stairs are susceptible to rot and water damage. Use lag bolts to raise deck posts and stair risers above footings to prevent water from seeping into the wood. Wood d...See Fluid and Lubricant Recommendations for more information. All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual. Recheck fluid level after filling. Cooling System. •2.0L L4 Engine Supercharged - RPO LSJ. 5.7 liters. 6.0 quarts. •2.2L L4 Engine - RPO L61.

Fasteners that list an angle are Torque to Yield (TTY). The specs listed are for stock fasteners. If you use ARP or other aftermarket fasteners, follow the instructions that came with your new hardware. Related Products:Camshafts & Valvetrain, Cylinder Heads, Engine Assemblies, Oiling Systems, Pistons & Piston Rings, Valve Covers & Dress-Up Kits.All specs are taken from Helms/GM documentation for a 2000 Model F-body. Special thanks to crackeregg for making these documents available in a digital format (saved me a lot of …old yukon said: Has anyone got torque specs for installing the 2000 4l60e to the 5.3L SLT engine, with np246 t/case. So many variations in specs out there . transmission to the engine. Flywheel to torque converter. Exhaust Manifold Bolts. heat shield to transmission. transmission rear mount. transmission cross member.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. to the LS1‐type engine. The LS1 flywheel is reused, and it goes . Possible cause: Chevy Silverado 2500 6.0L Main Cap Torque Specs (Side Bolts): 18 ft-lbs ....