Did you know?

The Litter-Robot 3 is equipped three LED lights to indicate certain statuses and faults with your unit. ... Once you’ve checked the condition, location, and orientation of the position sensor, reassemble the robot and initiate a clean cycle to determine if the problem was resolved. Replace the globe, making sure it is on straight and in its ...Litter Robot 3 not reversing during cycle. My Litter Robot 3 has been having a weird issue for the last two weeks. When it cycles, the globe rotates counter-clockwise until the hall sensor detects the magnet on the globe. It then stops, like it should. Then it's supposed to rotable clockwise to return to its home position, when the hall sensor ...I have completely cleaned it inside and out, nothing on the lenses. Robot Litter 3 Troubleshooting steps already taken: Cleaned/on-off /reset Additional information: #676303 (Web #1300025071 Ordered on 3/12/2018 ) Thank you so much in advance for your help! ... This issue indicates a defective DFI sensor and it needs to be replaced.Litter-Robot 3 DFI Kit + Pinch Detect Terminals Installation Litter-Robot 29.1K subscribers 46K views 1 year ago How to install a replacement DFI Kit + Pinch …Note: This problem is EXACTLY the same as this other post I found, which is why I’ve essentially just copied the description from there: Litter Robot Cannot Find Dump Position. Hardware concerned: Litter Robot III Connect. Software concerned: N/A. Troubleshooting steps already taken: unplugging it and plugging it in again; cleaning the …Litter-Robot 3: Litter-Robot 4: Footprint: 24.25″ x 27 ... Additionally, the Robot has integrated a new DFI sensor system, which enables reporting of small changes in the waste drawer’s fullness. In the app, this translates to a percentage-based readout that tells you exactly how full the waste drawer is at any time.To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes it resets it back to solid but every time now after my unit cycles it continues to ...LED blue flashing quicker than when the drawer is full and no button of the control panel is working. What should I do? Replace the draw sensors as mentioned in the coments?The issue that you are having would require replacing the DFI sensor and the 3 sets of pins so you can order the following parts from the following links: RobotShop Europe Litter-Robot 3 Open Air DFI Hardware (v2) Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 ...Purchase replacement pinch contacts and drawer full indicator (DFI) circuit boards here, or if your Litter-Robot is under warranty, log in to your …To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes it resets it back to solid but every time now after my unit cycles it continues to ...LED blue flashing quicker than when the drawer is full and no button of the control panel is working. What should I do? Replace the draw sensors as mentioned in the coments?1. Empty the Drawer. On the Litter-Robot, you have a drawer that collects the cat litter. If it becomes full, the blue light will blink rapidly. But if you throw out the mess, the lights should go off. Before returning the drawer to its compartment, remember to place a new liner into the container.To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base. 2.) Wait 10 seconds then plug the unit back in. 3.) Allow the unit to complete a start‐up cycle.The laser version only exists on a limited production run in 2020, and when those fail, they replace them with the original IR sensors. Despite my LR3 being out of warranty, they sent me a replacement IR and pinch sensor kit free of charge (this is the first and only time I've needed service).The updated DFI Kit is pictured on the bo om. 8-inch #2 Phillips screwdriver (20.3 cm) Preparation: 1 Press the Power bu on to turn the unit o and unplug it from the wall. …My litter robot 3 has been working perfectly until 2 weeks ago when it suddenly began getting stuck in the upside down position. ... 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app.If you need to replace the pinch detect terminals on your Litter-Robot and the unit is out of warranty, the process is simple and quick. For those who are th...

Then, after a minute, go into the Litter Robot driver, refresh, and see if the Cycles After Drawer Full (a counter in the Litter Robot that counts cycles after DFI IR sensor indicates a full drawer) count goes to 0. It’s supposed to go to 0 along with the cycle count when a reset is done.This topic was transferred to internal RobotShop Support. RobotShop Closed February 11, 2021, 1:00pm 10. Hi! We got a Litter Robot 3 about 6 months ago. Yesterday it showed a Home Position Fault (all lights blinking sequentially from red to blue). I can’t seem to find anything online that deals with this precise issue. ….Litter-Robot 3 is equipped with infrared emitters and sensors located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light. The Litter-Robot 3 is equipped three LED lights to indicate certain statuses and faults with your unit. ... Once you’ve checked the condition, location, and orientation of the position sensor, reassemble the robot and initiate a clean cycle to determine if the problem was resolved. Replace the globe, making sure it is on straight and in its ...In this case, the DFI sensor and the 3 sets of pins will need to be replaced so we will send you new ones under the warranty. The following videos will show you how to replace these parts: 1- Shipping address. 2- Phone number. 3- Serial number located on the back of the robot.

So one day, out of the blue, the same issue happened with our Open Air III, all 3 lights blinking and nothing works. What happens is that after restart the yellow light …Hi all, I'm having an issue with my 1 year old litter robot 3 where after every use the app says drawer full and the blue light flashes. I've followed all the litter robot troubleshooting steps including cleaning the lense and re-calibrating the sensor. I've created two support tickets and have been waiting over two weeks for a response from ...Note: This problem is EXACTLY the same as this other post I found, which is why I’ve essentially just copied the description from there: Litter Robot Cannot Find Dump Position. Hardware concerned: Litter Robot III Connect. Software concerned: N/A. Troubleshooting steps already taken: unplugging it and plugging it in again; cleaning the ……

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Litter Robot 3 infrared Drawer Full Indicator circuit boards an. Possible cause: The updated DFI Kit is pictured on the bo om. 8-inch #2 Phillips screwdriver (20.3 .